Search:

Type: Posts; User: ffrgtm

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. FS: 4x Raetech Prog. Strain Gage Amplifiers and Prog. Interface

    Selling 4 new Raetech Programmable Strain Gage Amplifiers. These are the "Without Housing" type, and have an 80Hz Low Pass Filter specified. The USB programming interface is also unused and for sale...
  2. Replies
    2
    Views
    1,476

    Hey Diebel, I came to the same conclusion. I...

    Hey Diebel, I came to the same conclusion. I ended up using zone based optimization rather than ply based. I am not sure if you have experience laying up composite structures or not, but we also...
  3. Replies
    9
    Views
    3,970

    I ended up buying a very cheap student license...

    I ended up buying a very cheap student license for Catia v5 to make use of their "Human Builder" for solving this problem. The basic driver model we were using in Solidworks worked fairly well for...
  4. Replies
    2
    Views
    1,698

    For predicting characteristics of planar sandwich...

    For predicting characteristics of planar sandwich panels subject to straightforward boundary conditions we've had success with ESAcomp. These simulations really lend themselves to situations where...
  5. These dampers are still available!

    These dampers are still available!
  6. Hello Adman, These dampers are still...

    Hello Adman,

    These dampers are still available. Assuming I'm correctly referencing an older invoice, these dampers should have the following valve codes: 2x Dampers with [Comp code 3 / Rebound...
  7. Replies
    71
    Views
    109,336

    Sticky: If you're interested specifically in composites,...

    If you're interested specifically in composites, take a look at the literature below... I've spent a small fortune on composites textbooks this year, yet these are the only ones I constantly...
  8. Hello Josh, These are still available, feel...

    Hello Josh,

    These are still available, feel free to private message me or email me at benjamin.kroon@mines.sdsmt.edu with any questions.
  9. Prices have been updated.

    Prices have been updated.
  10. FS: (4) KAZ Penske DA FSAE Dampers // (4) Uprated KAZ Damper Shafts

    The continued cannibalization of recent SDSMT FSAE entries has produced a surplus set of KAZ Double Adjustable 50mm Penske FSAE Dampers. These Penske DAs are in good condition overall, but I...
  11. Replies
    11
    Views
    5,993

    You're too kind Paul, I seriously appreciate that...

    You're too kind Paul, I seriously appreciate that advice. Perhaps my biggest roadblock in contriving a feasible process stemmed from the assumption that we needed to pull off a one stage cure. I...
  12. Replies
    11
    Views
    5,993

    Paul, Oddly enough, that's nearly the same...

    Paul,

    Oddly enough, that's nearly the same process we attempted last year... without much luck. One of the many things we failed to account for was the difficulty of conforming the core material...
  13. Replies
    21
    Views
    8,824

    From a Human Machine Interface perspective,...

    From a Human Machine Interface perspective, there's a reason that newer combat aircraft use control columns (centre-sticks) that function only on force input.. they deflect only enough to allow...
  14. Replies
    3
    Views
    2,150

    http://www.3dcadbrowser.com/3dmodels.aspx?download...

    http://www.3dcadbrowser.com/3dmodels.aspx?download=wr450
  15. AP Racing Calipers for Sale (CP4227-2S0 / CP4226-2S0)

    Due to some cannibalization, the calipers previously belonging to our 13' car are in need of a new home. I'm available to answer any questions or discuss selling arrangements.


    For reference----...
  16. Replies
    5
    Views
    1,969

    Everything in this auction has now been spoken...

    Everything in this auction has now been spoken for. Thanks to everyone for their interest!
  17. Replies
    5
    Views
    1,969

    The mychron is for sale again.

    The mychron is for sale again.
  18. Replies
    5
    Views
    1,969

    2 TC's sold, and the mychron is pending.

    2 TC's sold, and the mychron is pending.
  19. Replies
    5
    Views
    1,969

    Selling the evo3 with the harness I have laying...

    Selling the evo3 with the harness I have laying around, I didn't construct this DAQ harness, but the evo3 was sent to AIM and was verified to be 100% working.



    AIM3 + Harness : $600 shipped
    ...
  20. Thread: Locost....

    by ffrgtm
    Replies
    35
    Views
    10,386

    No I've decided to run without for now. I...

    No I've decided to run without for now. I reasoned that it would make more sense to run an electric reverse, and it wouldn't be very hard to put in as an after thought if I really need it down the...
  21. Thread: Locost....

    by ffrgtm
    Replies
    35
    Views
    10,386

    I'm currently building a "locost" with a hayabusa...

    I'm currently building a "locost" with a hayabusa engine. I ended up going with MNR (a uk supplier) simply because they seemed to have the fewest mistakes in their design. Having done far too much...
  22. Replies
    2
    Views
    946

    Mc'strut suspensions have poor camber gain and...

    Mc'strut suspensions have poor camber gain and also suffer from the phenomenon of gaining positive camber when steered dynamically, depending on how much SAI they have.

    The benefit of Mc'struts is...
  23. Replies
    17
    Views
    3,099

    There are two problems with a "soft" compound. ...

    There are two problems with a "soft" compound.

    First, cornering stiffness is going to decrease as compound stiffness decreases. FSAE cars tend to spend a lot of time at high slip angles so that...
  24. Replies
    34
    Views
    3,921

    clutch slip being torque multiplication

    clutch slip being torque multiplication
  25. Replies
    29
    Views
    13,882

    I really don't think that has anything to do with...

    I really don't think that has anything to do with autocross speeds....
Results 1 to 25 of 27
Page 1 of 2 1 2