Have you gotten your .lic file?
If so, did you put it in
C:\Documents and Settings\All Users\Application Data\SolidWorks?
We had plenty of issues with getting to go and we pretty much had to hard...
Type: Posts; User: Anday
Have you gotten your .lic file?
If so, did you put it in
C:\Documents and Settings\All Users\Application Data\SolidWorks?
We had plenty of issues with getting to go and we pretty much had to hard...
I tried sending an e-mail to that address and it was returned. We have a set of 13x8 steel rims with a dual 4x100 and 4x110.
PM me if you are still interested.
This means that when they use the quick jack to lift the jack tube 200mm above the ground, the rear wheels must lift off the ground. When the chassis is lifted, the wheels are in rebound or 'droop'.
none of the frames anyone will sell you will be legal with the new rules for 2009.
It looks like you will have to do it yourself.
performing that comparison is your job as an engineer. you cannot demand the research others have put their own time into.
you could possibly make a few requests for information, but you cannot...
When they say continuous, they mean a single length of tubing.
That means it's gonna have some bends.
with a lot of patience and sanding, you can make respectable bodywork out of bondo-glass or any inexpensive fiberglass fabric and polyester resin.
i have never seen a quality aluminum body, and to...
has anyone else had problems with roll hoops in the CosmosWorks2007 Beam Analysis? According to the help menu and my experience, it can only analyze straight beams.
Unless i'm missing something,...
it's the september 2007 issue. vol 17 no 09.
i just happened to have it within reach, it's some interesting stuff. some cars are featured for good reasons and others are featured for being quirky...
Every little bit counts. Every fraction of an ounce adds up.
Last year we set a weight savings percentage goal and met it. Every part/system on the car had to be XX% lighter than the one on the...
plastic tube can get pretty unhealthy too.
when PVC gets hot it releases chlorine gas. that's some pretty nasty stuff too.
but welding is a lot easier with hot glue, it's a lot like MIG.
If you check the 2008 Rule Change Summary on SAE.org you'll see that it's the main hoop bracing that cannot directly pass loads through the engine. The main hoop bracing must be connected to or...
This may not be the best thread to ask this question. Those of us who are members of the Tire Test Consortium paid for this data that we could not get ourselves. I would think Cal-Span would...
Is anyone else curious about how they will define the 5th Percentile female as a Vehicle Design Objective? They didn't add any more information beyond what it said in the Rule Change Summary.
From our experience, 35 degrees is about all you want to design for. That's what ours was last year and there was some 'looping' of the shaft if not perfectly alligned and supported. That is not as...
Anyone been bugging the rules committee about a date for the 2008 Rulebook?
Aluminum is definately the norm.
We got ours last year from Sprocket Specialists.
I'm sure you could find plenty of options if you just did a search.
Has anyone heard when the Official 2008 Rules will be released? I'm interested to see some of the details for these changes.
yea, we mounted our shoulder belts that way on any car of ours I've seen. Just wrap the belt around the tube and use the bracket on the belt to secure it closely to the tube.
Just be sure that the...
Taylor Race has the sprockets for the honda quaife and I am pretty sure that Sprocket Specialists will have something that you can work with or at least sprocket blanks.
We are planning on bringing our '06 and '07 cars. The drive back will kinda suck since it'll be the end of our spring break and we have class monday. I'm sure it will be worth it though.
Just...
Unfortunately we found out that the "Yamaha 03 R6" model is not as accurate as we were led to believe. As it turns out, the crankcase is actually a half inch shorter, while the engine mounts are...
We have a similar sanding tube notcher, which is pretty easy as far as a perpendicualar or common angle goes.
We also use angled pieces from the waterjet to place tubes at the appropriate angles for...
I don't know where your origin is, but you could offset planes normal to the axis of the part at the different z-coordinates. That way when you sketch on those planes you only have to dimension an X...
We actually assigned new guys a homework part to model. If they are worth something and want to do something we give them something to model since it's a great way to learn software packages and how...