Search:

Type: Posts; User: Grant Mahler

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Where is the shipping company sending the car to?

    Where is the shipping company sending the car to?
  2. Replies
    23
    Views
    7,747

    <BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by jalai:
    Can You tell, how You measure DT with...
  3. Replies
    49
    Views
    10,609

    Karnak: After we are done pushing Drew's car...

    Karnak: After we are done pushing Drew's car inside, we will...

    Ans:Washer
  4. Replies
    14
    Views
    3,740

    <BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by Ockham:
    Be warned that if you're using fuel injection...
  5. Replies
    23
    Views
    7,747

    Yea the numbers I posted were @ 12v. At 14.4 they...

    Yea the numbers I posted were @ 12v. At 14.4 they will be faster.
  6. Replies
    23
    Views
    7,747

    1.5ms is a very safe time to assume it takes to...

    1.5ms is a very safe time to assume it takes to get to fully developed flow. 1.5 is what is quoted in the MS manual.

    1.0-1.1 is what most of the injectors I saw tested took.

    Depends primarily...
  7. Replies
    18
    Views
    4,276

    <BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by ben_fordham_uoitmotorsports:
    Thanks Adam.
    I'll look...
  8. Replies
    612
    Views
    150,814

    Please take video!

    Please take video!
  9. MS2 has fine DAQ. The best way to do it is to use...

    MS2 has fine DAQ. The best way to do it is to use the standalone datalogger, which is cheap and stores to an SD memory stick. Or you can ebay an old Palm and datalog on that.

    I would imagine the...
  10. Thread: AWD car

    by Grant Mahler
    Replies
    22
    Views
    5,280

    One of the Italian teams ran rear steer I...

    One of the Italian teams ran rear steer I believe, not sure about rear drive, in 2007 at California. Firenze I believe.
  11. For a couple "dumb rednecks", some sweet cars out...

    For a couple "dumb rednecks", some sweet cars out of 'bama...
  12. <BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by Mikey Antonakakis:

    Grant,
    I did some searching and...
  13. <BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by neon spark:
    ooh .. patclark
    dude i used somne short...
  14. Replies
    33
    Views
    11,556

    Jen posted this well over 2 years ago. ...

    Jen posted this well over 2 years ago.

    Cardiff had 5 engines.

    STOP BUMPING THIS THREAD! ITS BEEN DEAD FOR 2 YEARS! FIND ANOTHER WAY TO GET AN ENGINE!
  15. Replies
    5
    Views
    1,928

    The bold links at the top of the page.

    The bold links at the top of the page.
  16. Replies
    23
    Views
    5,825

    Try 4ms cranking fuel.

    Try 4ms cranking fuel.
  17. Replies
    22
    Views
    6,457

    Does MS2/E deal with cranking timing better than...

    Does MS2/E deal with cranking timing better than a year ago?

    We had a hell of a time getting our cranking timing values to work out. Despite setting a cranking value, the MS2/E wouldn't actually...
  18. Replies
    22
    Views
    6,457

    <BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by abinley:
    Turn your cranking rpm up as high as it goes...
  19. Replies
    22
    Views
    6,457

    ASE only matter once you pass the crank threshold...

    ASE only matter once you pass the crank threshold into running...This is a value (RPM) you set.

    I strongly doubt its the ASE that is the issue at the moment.

    Pull a plug, ground it against...
  20. Replies
    12
    Views
    4,241

    Nevermind.

    Nevermind.
  21. Replies
    23
    Views
    5,961

    For the purposes of this competition, I...

    For the purposes of this competition, I respectfully disagree. I don't think that running to the absolute edge in terms of utilizing materials to their limit is the best way to earn points in this...
  22. Replies
    23
    Views
    5,961

    Actually, fixitmattman is right. The fatigue...

    Actually, fixitmattman is right. The fatigue calculations aren't difficult, and are straightforward out of the book. Pick your component. Is it loaded in bending, compression, tension or some...
  23. Replies
    9
    Views
    3,786

    <BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">Originally posted by D Collins Jr:
    Hi Scott,

    Be careful posting that...
  24. Replies
    18
    Views
    5,813

    <BLOCKQUOTE class="ip-ubbcode-quote"><div class="ip-ubbcode-quote-title">quote:</div><div class="ip-ubbcode-quote-content">

    I think you missed the point. I don't think they are at that stage of...
  25. Replies
    18
    Views
    5,813

    Do what EVERY other successful team has done: go...

    Do what EVERY other successful team has done: go to a dealership and MEASURE it. These are not complicated things, and the board gets requests like this all too frequently from people too lazy to go...
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4