Search:

Type: Posts; User: MOTO909

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    10,760

    I don't know about the liquid plastidip but the...

    I don't know about the liquid plastidip but the spray on will last for awhile and then peel off from use.
  2. Replies
    4
    Views
    5,510

    What hole pattern and bolt size?

    What hole pattern and bolt size?
  3. Replies
    8
    Views
    7,386

    The first year we put two or three small holes in...

    The first year we put two or three small holes in it because people used knives/screwdrivers carelessly near the fabric. This (second) year there is no holes. It can survive flailing leg egress...
  4. Replies
    8
    Views
    7,386

    As Kevin said super light, but not resistant to...

    As Kevin said super light, but not resistant to tears. I would also add that it is cheap both in the real world and the cost report. We have used it for 2 years and I expect it will continue for...
  5. Large selection of items on eBay, make me an offer

    I have a large selection of items I am selling for our team including:

    Ball Bearings
    Pillow Block Bearings
    Wheel Studs
    Ball Joints
    Rod Ends
    Spherical Joints
    AN and NPT hose fittings...
  6. Replies
    16
    Views
    8,842

    It sounds like you are only looking at flexible...

    It sounds like you are only looking at flexible stainless steel braided lines. What you should look into is using steel hardline between the front and rear of your car.
  7. Replies
    2
    Views
    4,868

    Engine is sold.

    Engine is sold.
  8. Replies
    3
    Views
    5,533

    I asked our contact at Motec and he says...

    I asked our contact at Motec and he says everything except traction control is enabled. It looks to me on their website that standard memory was 512 kB and wasn't upgradeable. I can't guarantee but...
  9. Replies
    3
    Views
    5,533

    I don't know for sure I'm going to assume it is...

    I don't know for sure I'm going to assume it is the lowest amounts that were available. Somebody may get a surprise and receive more than they paid for.
  10. Replies
    3
    Views
    5,533

    Motec M4 ECU for sale - Make an offer

    ******SOLD*******

    We have a used Motec M4 ECU for sale, this came off an old car. We currently use the Performance Electronics PE3 and have no use for the Motec M4. This ECU just came back from...
  11. Replies
    1
    Views
    3,178

    Make me an offer. I would let these go for cheap.

    Make me an offer. I would let these go for cheap.
  12. Replies
    2
    Views
    3,041

    Check out my for sale thread. ...

    Check out my for sale thread.

    http://www.fsae.com/forums/showthread.php?11577-Wilwood-PS-1-calipers
  13. http://www.rcvperformance.com/categories-cv-axles....

    http://www.rcvperformance.com/categories-cv-axles.aspx?catID=RCVP_FORMULA_FSAE_ALT

    These guys have what you need. Gundrilled shafts with integrated tripod housings.
  14. Replies
    1
    Views
    3,178

    Wilwood PS-1 calipers

    Qty:2 120-5453 Passenger Side, Piston Diameter (in):1.000 in., Thread Size:1/8-27 in. NPT
    Qty:2 120-8373 Passenger Side, Piston Diameter (in):1.120 in., Thread Size:10mm x 1.25
    Qty:1 120-8374...
  15. Replies
    2
    Views
    4,868

    more pictures of the engine

    more pictures of the engine
  16. Replies
    2
    Views
    4,868

    2001 Kawasaki ZX6R engine, needs clutch

    This engine was taken out of our last 4 cylinder car which was our 2007 car. When the clutch needed to be replaced we swapped in another ZX6R engine that we had in storage. This engine was running...
  17. Replies
    11
    Views
    8,753

    We still have the items listed below. 2...

    We still have the items listed below.

    2 Hoosier 20x7.5-13 Wet
    2 13" wheels 8.25" wide 3.00" backspacing. Front is offset 5"
  18. I have an M4 that we will be looking to sell...

    I have an M4 that we will be looking to sell soon. I just sent it in to a contact at Motec to have it checked out before we sell it. I didn't want to sell it without knowing it was fully...
  19. Replies
    5
    Views
    3,762

    I would suggest finding a local company that will...

    I would suggest finding a local company that will do it for free rather than paying cash. Surely in the Dallas area there is multiple companies with tube lasers. I would think at least one would...
  20. Have any teams received a steering rack from...

    Have any teams received a steering rack from Pro-werks? I ordered in February and I am still waiting. I think we are going to avoid using it next year but for now we will probably end up stealing if...
  21. Replies
    5
    Views
    4,214

    Kind of an old post but wanted to say that Dave...

    Kind of an old post but wanted to say that Dave has been quick to respond and is great to order from. We purchased all of our rod ends and spherical bearings from them. I would recommend purchasing...
  22. Replies
    5
    Views
    3,570

    High Performance Vehicle Engineering no longer...

    High Performance Vehicle Engineering no longer has the cutter required to do these splines.
  23. Thread: Torsen Splines

    by MOTO909
    Replies
    6
    Views
    3,720

    I confirmed with Torsen on the phone it is 34...

    I confirmed with Torsen on the phone it is 34 degree pressure angle.
  24. Thread: Torsen Splines

    by MOTO909
    Replies
    6
    Views
    3,720

    Is anybody able to confirm what the pressure...

    Is anybody able to confirm what the pressure angle is for the Torsen university special?
  25. Replies
    5
    Views
    20,327

    I hate to continue a thread like this but I have...

    I hate to continue a thread like this but I have to ask is that Loctite 290 you used? How many years have you done this and has it ever broken down in fuel? Have you tried it with e-85?
Results 1 to 25 of 33
Page 1 of 2 1 2