Search:

wheels are no longer for sale, sorry.

We have some RC's for sale contact me privately at hwood AT uvic DOT ca

13 X 7 in keiser three piece wheels, 4 X 100mm stud pattern, ~5 in offset. Some damage but repairable. Mounted with old hoosier 7 in tires. Too wide for us. $200 US offers/trades welcome. email:...

13 X 7 in keiser three piece wheels, 4 X 100mm stud pattern, ~5 in offset. Some damage but repairable. Mounted with old hoosier 7 in tires. Too wide for us. $200 US offers/trades welcome. email:...

Is the the engine still for sale? What year is it?

thanks

Rob,

I grabbed the thank you poster for SkyTrac Systems. They look great guys.

Steve

Minutes Nov 25

everyone who paid the 50 fee gets a team t-shirt. If you want a hoodie, toque, hat you will have to pay extra, contact tifenn for prices.

Wheelends: For the spindles, Vangear...

They are on the bottom shelf in the office in a grey package.

Eric

Meeting Minutes Nov 18

UPDATES

Wheelends<UL TYPE=SQUARE><LI>need annealed steel to machine splines but metal supermarkets does not have all of what we need, Tifenn is checking out other types...

Sorry, we dont

Hayden Uvic

Meeting Minutes Nov. 4

Thanks to all who helped out at the consumer electronics show.

There will be a spindle design meeting in the ELW lobby 5pm Wednesday.

Passaree needs your member...

Meeting Minutes oct 28

Consumer Electronics show this weekend thanks to all who are helping out. Its at the Perks arena behind Tillicum mall. Hours: Fri 2pm(setup);Sat 9-5; Sun 10-5.

Spindle...

The resistance looks okay on the stock ones

Hayden

Hi Colin,

For simplicity's sake I'll work with Rob on ordering the ECU. Is there any reason we can't use the stock injectors with the PE ECU? I will check tonight if they have the appropriate...

We are meeting at the garage around 9am, see you there.

Hayden

The minimum resistance for the coil packs is 1 ohm and we measured 1.6ohm so we are ok. Here are all of the numbers off of the coils: 127900-4400, J04440, 06C15. Unfortunately the RC injectors have...

Hey Colin,

I called PE already and got some ordering info. We have to test the minimum resistance of our coils and make sure they are inductive, I will do that tonight We have to test our...

Hey Colin,

I called PE already and got some ordering info. We have to test the minimum resistance of our coils and make sure they are inductive, I will do that tonight We have to test our...

I went to Vic Cycle salvage and picked the cover up for $114.50 hope that's
okay. We need to make a bushing for the cover where the starter shaft goes
as they are different sizes. We can use the...

Garage thursday night around 5pm

If anyone is available can you please respond to the newsgroup. I would like
to figure out the engine cut-off/shifting problem and Vic. motorcycle
salvage has an...

October 21 Meeting minutes

We have a 10 X 10 booth at the consumer electronics show Nov 1-2 location TBA. Please sign up, we need peole to set up/down and to tend the booth. Sign up sheet will...

Hi Tifenn,

Here is the page I found on the driveshafts from taylor race engineering there are cv dimensions if you scroll down

http://www.taylor-race.com/pdf/ACF319.pdf

Hayden

October 14 Meeting Minutes

Great job by all in the garage on Saturday!

UV04 Update: The engine runs!! Yipee. Spindles will be done by friday: Armando is machining in the mornings and eric will...

October 7 Meeting Minutes

A door was found open at the garage. Remember to check them when you leave.

Everyone can sign onto the FSAE forum now. just use ID:uvicfsae and password:BicMack. ...

I will be in the garage with Duncan , Pat and hopefully Steve to try and get the engine running thursday at 2pm