Search:

Type: Posts; User: Cunningham

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    6,041

    Thanks John!

    Thanks John!
  2. Replies
    0
    Views
    3,174

    Cost of Mold Tool (Cost Report)

    deleted 10 char
  3. Replies
    7
    Views
    6,041

    Trent, thanks! I start in late July. I would...

    Trent, thanks! I start in late July. I would prefer to live no more than 20 minutes away from Dearborn, but could do 30 minutes if the neighborhood was really cool. For fun I'd like go to concerts,...
  4. Replies
    3
    Views
    1,611

    We looked very closely at using a servo motor....

    We looked very closely at using a servo motor. There are some high-torque "smart motors" that could be used with a gearbox; however, significant setup and testing time would likely be required and in...
  5. Replies
    7
    Views
    6,041

    Where to live for Ford

    Hi Everyone,

    I was fortunate enough to be offered a position at Ford in Dearborn (largely due to my FSAE involvement) and am looking into housing. What are some good areas to check out that have...
  6. Replies
    37
    Views
    20,383

    While the Lincoln Airport is amazing and the city...

    While the Lincoln Airport is amazing and the city itself is pretty cool, moving the competition back to California (or perhaps Washington state) would result in many more interested volunteers and...
  7. Replies
    11
    Views
    5,722

    We are using a left and right mold and did so on...

    We are using a left and right mold and did so on our last chassis--but I would not necessarily recommend this route. By using a top and bottom mold you can set all suspension pickups with the mold...
  8. Thread: fuel tank

    by Cunningham
    Replies
    7
    Views
    2,776

    I agree with Nick. It is your job as an engineer...

    I agree with Nick. It is your job as an engineer to at least do some research/work yourself before asking for "the answer."

    We used an aluminum that is know for good bend-abilty and low stress...
  9. Replies
    2
    Views
    1,673

    I have 3x STACK 100mm sensors available. Shipping...

    I have 3x STACK 100mm sensors available. Shipping would be from California.
  10. Replies
    41
    Views
    12,334

    Many members of my team are in full support of...

    Many members of my team are in full support of delaying the rules change until next year when they can be distributed before conceptual and detailed design. Here are some reasons:

    * FSAE cars...
  11. Replies
    0
    Views
    1,170

    Three STACK Linear Pots

    Hi All,

    I'm selling 3 STACK brand linear potentiometers. The shipping address will have to be in the US please. On to the SPECS:

    Brand: Stack
    Model: ST973
    Stroke: 4"/100CM
    Connector: loose...
  12. Replies
    40
    Views
    25,624

    Thanks Randy. Great shots!

    Thanks Randy. Great shots!
  13. Replies
    1
    Views
    1,981

    How are you laying up TeXtreme?

    Hi All,

    I am looking into using TeXtreme to construct wings for the 2015 Cal Poly FSAE car.

    Please forgive me if I missed this in my search, but how are you all laying up your TeXtreme?...
  14. Thread: 13" Wheels

    by Cunningham
    Replies
    0
    Views
    1,030

    13" Wheels

    Looking for a set right away. Bolt pattern is not so important as long as the face between the bolt pattern is flat.

    Please reply to
    cpfsae
    ACHT
    gmail
    DACHT
    com
  15. Thread: WINGS

    by Cunningham
    Replies
    226
    Views
    66,636

    Thanks Harry and Julian.

    Thanks Harry and Julian.
  16. Thread: WINGS

    by Cunningham
    Replies
    226
    Views
    66,636

    All, I've done some searching--without...

    All, I've done some searching--without success--for clarification on rule T9.3:

    T9.3 Minimum Radii of Edges of Aerodynamic Devices
    T9.3.1 All wing edges including wings, end plates, Gurney flaps,...
  17. The equation is pretty simple actually. Test...

    The equation is pretty simple actually.

    Test wing + rigid mount + desired speed + redneck truck = yes/no

    215

    Seriously though, we hit the wing at our target speed and had 0 damage to the...
  18. Replies
    37
    Views
    22,995

    Harry, A thread might be good. Even if the...

    Harry,

    A thread might be good. Even if the rules have been decided as Michael believes, perhaps this could ensure a sufficient delay before roll out for the teams on a 2 year design cycle.
    ...
  19. Replies
    37
    Views
    22,995

    As the design season for 2015 is beginning, this...

    As the design season for 2015 is beginning, this thread should probably be revisited.

    My team has generated a list reasons we feel are highly supportive of not implementing a spec aero package...
  20. Replies
    2
    Views
    1,279

    We have 3 for sale. Stroke is about 200mm. The...

    We have 3 for sale. Stroke is about 200mm. The body is long for an FSAE car's suspension travel, but they can be made to work with the proper mounts. $150 for all 3.
Results 1 to 20 of 20