Search:

Type: Posts; User: Karam El Hady

Search: Search took 0.01 seconds.

  1. Replies
    15
    Views
    19,981

    torsional stiffness

    Hi everyone i'd like to know how is torsional stiffness is good for chassis and how is it related to suspension force and what is the optimum valve of torsion stiffness for space tubular frame ...
  2. Replies
    2
    Views
    2,833

    the tolerance of tube size

    first of all ; what i want to say next it just a discussion . When i read in learn and compete book i found this (there is a tolerance in size of tubes )
    page (34)
    1162
    what i want to ask about...
  3. Replies
    1
    Views
    2,076

    main hoop bending

    Hi......I'd like to ask about main hoop bending when we bent the main hoop like cad model we got two main hoop but we face problem in image (1) when we bent it we got bending right in the middle of...
  4. Replies
    3
    Views
    2,668

    Jonny Rochester can you tell me the equation i...

    Jonny Rochester

    can you tell me the equation i can use to calculate the stress on the member using the maximum torque and the engine weight
  5. Replies
    3
    Views
    2,668

    engine supporting

    I'd like to ask if these red members in image (1) is good enough to support the engine well .all these red members have 20 cm length So are these member will be good and save ??
    1156
    and are...
  6. Replies
    5
    Views
    4,445

    the chassis height and C/G

    what is the optimum clearance between the lowest member in chassis and the ground ?
    Is 80mm a good clearance ? and if i make the clearance lower is that will make the C/G lower ??
  7. Replies
    2
    Views
    2,251

    Cockpit Opening test

    I put the template which used to ensure that the opening giving access to the cockpit is of adequate size in the chassis like images now i want to known if the size or the area
    of the cockpit is...
  8. Replies
    1
    Views
    1,935

    chassis rules

    the rules of chassis said " The Main Hoop must extend from the lowest Frame Member on one side of the Frame, up, over and down the lowest Frame Member on the other side of the Frame
    So which of...
  9. Replies
    6
    Views
    3,702

    Hi Claude Rouelle i made(upper maim hoop...

    Hi Claude Rouelle

    i made(upper maim hoop bracing support) member horizontal like pic because i fixed suspension point on it so now i related with plan i can't make the member higher to go the...
  10. Replies
    6
    Views
    3,702

    chassis question

    I'd like to ask if welding (the main hoop bracing and main hoop bracing support ) members in the the point in black circle instead of the point in red circle like pic is permissible and right ?
    ...
  11. Replies
    1
    Views
    1,964

    Chassis supporting

    Hi... I'd like to ask if the red member in the chassis in image (1) need support member ?

    1147
    In image (2) ...if i weld engine support member(the yellow member) in the red member like pic i need...
  12. Replies
    0
    Views
    1,869

    Chassis design

    hello
    i'd like to ask if using square tube like pic is permissible
    1131

    i have 3 Frame Members on each side of the vehicle; an upper member; lower member and diagonal brace and in our...
  13. Replies
    7
    Views
    6,412

    Hi cody the rules is obvious in this section ...

    Hi cody

    the rules is obvious in this section
    the boundary conditions "Fixed displacement but not rotation of the bottom nodes of both sides of the main roll hoop and both locations where the...
  14. Replies
    3
    Views
    3,032

    Adam & Michael thanks for your interest :)

    Adam & Michael

    thanks for your interest :)
  15. Replies
    3
    Views
    3,032

    SES enquiry

    Hello everyone.

    I'm from Egypt and am doing the frame on our first FSAE car build.

    that's my first time to fill SES form

    I have some questions about the number of members classified as...
Results 1 to 15 of 15