Open forum for all things Formula SAE related.
Hi all, I've put this list together last year, and made it available to guys on our team and will do the same this year. It's up to individuals...
Unfortunately, there is no LINKS page on the FSAE.com website, so I put one together to help everyone. If you have any more, just post a reply,...
The third round of testing at Calspan will be conducted on 21-22 June 2007. Four constructions are scheduled to be tested: + Michelin 21x8-13...
If you're new here, it's very likely that among almost 5000 forum members and close to 50,000 posts, your question has been asked. Well, at least...
Can anyone recommend some reading material on heat exchanger design? So far I hav been relying on intercooler theory on the web and old fluids and...
Greetings all, I’ve been sitting down in the odd spare minutes I’m getting here and there, and slapping together a bit of a thesis about what I...
There have been a number of papers written by participants of FSAE on various Formula SAE topics. Your university library may have the ability to...
The FSAE team at Western Washington University has agreed to host a CAD file library for everyone. This will be a central place for teams to share...
Everyone, I would like to announce a new set of tutorials being created by SolidWorks, specific to the Formula SAE competition. The first video,...
Does anyone have the web links to either the kaizer or bbs 3 piece wheels, which is better?
In calculating the mechanical force generated by a 3 piston calliper(2 pistons on one side and one on the other side), what effective piston area...
Hi, I have just started using solidworks/cosmos for some FEA analysis but I can't figure out how to model 3 point bending. This sould be very...
Has anybody here rebuilt a set of 3-piece wheels? We have a set of Keizers that are leaking that we'd like to repair. Would it be as simple as...
Hello, I have a quick question, for people that run Keizers or similar. If I recall correctly, there are like 16 bolts holding the wheel together....
Hello everybody, i have a questions about the Rule 3.3.5.5 Mechanically Attached Roll Hoop Bracing. Can anybody elaborate me the "capping...
Just a question asking for a few peoples interpretation of a rule. "High pressure over 15psi fuel systems must utalize protected hose with either...
It shouldn't be a issue for us, since we have 2 plans for it (one would have the exhaust 'break' the rule the other wouldn't), but what do you guys...
I was wondering if any of the teams that run 3/8-24 wheel studs run aluminum lug nuts. If so where did you guys get them. I can only seem to find the...
http://cgi.ebay.com/ebaymotors/Mini-Supercharger-Cycle-...temZ8032405346QQrdZ1 Maybe not a fully legit topic for this forum, but I know there...
Does anyone have a good source to buy 300m steel from? I'm looking for axle shaft material. I see that Mark Williams sometimes dumps some on EBAY...
Does the template have to go straight in horizontally or can we also move it vertically if required? This might be a silly question but we are having...
Hi, Need a clarification on scrutineering procedure for the 350 x 350 template. We have our steering rack going below the driver's knees, very...
How has the new 36" rule affected your design? Are we going to see much taller main roll hoops this year?
Hi, I was encountered a problem to start my assignment. Could anyone here knows how to draw a 3D drawing in Patran2010? Thanks in advance.
I was wondering what models teams used for dimensioning the cockpit. Is there somewhere where you can download models or did every team design there...
Hey guyz! We are lokking for 3D-data for a Honda pc35 engine. The housing will be enough. We need it to design our frame so we don't have to do...
Hello All I would like to announce the 3rd Annual University of Toronto Shootout. We have been hearing from a lot of teams as to whether we would...
There was discussion of warp stiffness in another thread, and the coupling of pitch / roll / ride / single wheel bump stiffness in general. ...
Please click on the link below, skip the intro, and wait for the bike to load. Click on the bottom most square and watch the video. Link ...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules