Open forum for all things Formula SAE related.
The third round of testing at Calspan will be conducted on 21-22 June 2007. Four constructions are scheduled to be tested: + Michelin 21x8-13...
Greetings all, I’ve been sitting down in the odd spare minutes I’m getting here and there, and slapping together a bit of a thesis about what I...
Hi all, I've put this list together last year, and made it available to guys on our team and will do the same this year. It's up to individuals...
Unfortunately, there is no LINKS page on the FSAE.com website, so I put one together to help everyone. If you have any more, just post a reply,...
The FSAE team at Western Washington University has agreed to host a CAD file library for everyone. This will be a central place for teams to share...
Can anyone recommend some reading material on heat exchanger design? So far I hav been relying on intercooler theory on the web and old fluids and...
If you're new here, it's very likely that among almost 5000 forum members and close to 50,000 posts, your question has been asked. Well, at least...
There have been a number of papers written by participants of FSAE on various Formula SAE topics. Your university library may have the ability to...
Everyone, I would like to announce a new set of tutorials being created by SolidWorks, specific to the Formula SAE competition. The first video,...
Hi guys, i have a question regarding the steering racks....i have gone through previous posts and i have noticed that some teams make their own...
Guys we are a rookie team. Doing FSAE for the first time. Would like to know if this suspension geometry is OK? any suggestions and advice is more...
hi guys, what do u think about 4 wheel steering in our cars????? obviously, the handling will be better but what about the packaging...
So I have been searching for some time about dry sump systems. There is a lot of good information out there, but one problem I keep running into is...
hi people... i was wondering what is the connection of rack ratio for a example 12:1 and the c factor (mm per 360 deg)...i am a bit confused ...
Can anyone help me to perform acoustic analysis of CHASSIS. Thanks
Hello, Is there anybody with some ADAMS/Car experience? Thank You Ted
Hi, Motion Ratio is defined as MR=wheeltravel/springtravel. Now I have no confusion if my pushrod/spring is perpendicular to my lower wishbone....
I do not yet have parts to measure, but I need to finish designing drive train parts. Can someone please tell me the overall width of a 520 chain...
I was just informed by a very unfortunate event via the ImechE facebook page. "A serious incident involving a driver from Dundee University’s...
While the topic of diesels is out there, I also wanted to toss some of the new small rotaries into the ring. The Axiro XR 50 is a bad little...
Hi, i have tried to look on the forum for an answer to my question, but didn't find anything useful. I am using tire data from TTC, but need to...
hi people... i was wondering how i can determine the steering angle of my wheels (ackerman percentage), to create slip angle of my choise...i make...
have any one checked for his dry sump oiling system i want to know his data ???? my engine is "GXSR 600-07" -oil temp from engine and to engine ...
Does anyone have any good marketing and promotional quotes from influential people that support FSAE/FS that they would like to share? In...
Hello all, Unfortunately, and fortunately, our 2007 GSXR motor is in Florida right now getting a 3d scan done on it, but i need to know how much...
Hey All, I am wondering how the teams using the large Thin Section bearings in their uprights seal them? (Assuming they were not purchased with an...
I'm trying to find a good place to buy wheel bearings. We're looking to use a single double row angular contact ball bearing inside our upright. It...
Hey guys we are a newbie team from Pakistan planning to compete in Formula Student2012. We are facing problem in evaluating the best possible...
I need help measuring the displacement for the of the master cylinder. I know the pressure input going into the caliper and the master cylinder. I...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules